Free network traffic monitor software for linux

Network Traffic Analyzer analyzes the network traffic on multiple network devices and creates HTML statistics with some network usage graphs. Sometimes it is good to know, how the network is used, how many bytes were received and how many bytes were sent.Therefore, here is Network Traffic Analyzer, which creates simple network usage statistics.


Such statistics can tell you, how good your network connection really is (who cares about what Internet provider say, when was the network down, which time is the best time for downloading large packages of data etc. etc. Or with this software you can just better imagine, how many traffic can your home computer generate.

Skipole Network Monitor project is a simple network monitor with built in web server.

It allows the user to input host IP addresses, it then pings these hosts every five minutes and displays their status via a built-in web server, on port 8000.

So calling http://your_pc_address:8000 will display pages showing green, yellow or red host or group symbols.

Each host is pinged four times every five minutes, and symbols are displayed as:

green : if three or four pings are successfull
yellow : if only one or two are successfull
red : if all four fail

As well as hosts, group symbols are displayed, and can be opened to show hosts, or sub-groups nested within. The operator can create groups, and sub-groups via the gui.

Network Pipemeter is a tool for measuring available bandwidth between hosts. nepim is also useful to generate network traffic for testing purposes.
nepim operates in client/server mode, is able to handle multiple parallel traffic streams, reports periodic partial statistics along the testing, and supports IPv6.
nepim has been tested under Linux, Solaris and FreeBSD, though it should work under other platforms as well. If you manage to build nepim for different systems, please send the patch.
- nepim is useful to assess the throughput at the transport layer (TCP or UDP) as seen by applications.
- nepim runs single-threaded and should impose very light burden on your CPU. Unless, of course, your testing hosts have relatively high network bandwidth compared to low CPU power.
- One single server can service multiple clients simultaneously.
- As of nepim 0.11, one single client can interact simultaneously with multiple servers. For instance, suppose you want to test, from a single client, two remote servers, one located at 10.0.0.1,2000 and another at 192.168.0.1,3000:
- nepim -c 10.0.0.1,2000/192.168.0.1,3000
- The server listens to both TCP and UDP sockets. The client by default uses TCP sockets. Use the "-u" client option to switch the client operation to UDP.
- By default, only the server sends traffic towards the client. Use the "-s" client option to reverse the behavior, then only the client will send traffic. Use the "-d" client option to make both client and server to send traffic.
- Use the "-r" client option to establish an upper bit rate limit. Without a rate limiting option, nepim sends as fast as possible. See also "-R" below. Please notice the rate is specified in bps (bits per seconds); for instance, the following example states a rate limit of 100,000 bps (100 Kbps):
- nepim -c 10.0.0.1 -r 100000
- Use the "-R" client option to establish an upper "packet" rate limit (outbound rate limit for transport layer segments). Without a rate limiting option, nepim sends as fast as possible. If both "-r" and "-R" are given, nepim limits the sending rate at the lower of those bounds.
- Use the "-n" client option to run multiple parallel traffic streams.
- Use the "-b" server option to make the server to listen on specific local addresses.
- Use the "-6" option to disable IPv6 support.
Enhancements:
- Support for randomizing the UDP destination address/port has been added in order to put stress on routers with on-demand (dynamic) forwarding table caches.

Network Probe and protocol analyzer is the ultimate tool for traffic-level network monitoring, troubleshooting, analysis,
If your network is crawling to a standstill, and you suspect there might be a problem with the network traffic, Network Probe will quickly help you identify what is causing the problem, show you who is generating any troublesome traffic, and where the traffic is being transmitted.
Network Probe will collect traffic statistics for all protocols, hosts, and conversations on your network, and show you all the top talkers and listeners on your network. Hosts generating large amounts of traffic such as music and movie streaming, playing online games, or listening to streaming media are easily identified.
Main features:
- Watch in real time which protocols are used on your network
- Watch in real time which hosts are active on your network and the Internet
- Watch in real time which conversations are taking place on your network and to and from the Internet
- Watch in real time detailed protocol statistics per host
- Watch in real time detailed protocol statistics per conversation
- Watch in real time network card details for your network
- Watch traffic amount of selected entries relative to the total and filtered traffic
- Watch traffic amount over time for any host, conversation, and protocol
- Watch in real time network throughput for the entire network segment
- Inspect detailed logged statistical data from days and weeks earlier
- Filter out and search for selected protocols, hosts, conversations, and network cards
- Sort network traffic by amount of data transmitted or received
- Export network traffic statistics data
- Configure users with restricted access to statistical data
- Password protected login

Traffic Prioritizer is designed to run on a Linux router and prioritize users traffic by their bandwidth consumption.

It is aimed to shape the "bandwidth greedy" clients (P2P, YouTube, IPTV, etc.) so that the ones who are just browsing do not lack bandwidth.

check_tcptraffic is a simple Nagios plugin to monitor network traffic on Linux systems.

Usage:

usage:
-c crit critical
-w warn warning
-i iface network interface
-r initialize
-v verbose

System Health Monitor for Linux is a handy python program that will setup your system to generate RRD Graphs of network interface traffic, system load, memory usage, disk space and inode usage and graphs of the number of running processes.

System Health Monitor features a user-friendly interactive configuration mode and auto-generated html pages. Just point your web server to the health_html directory to get an overview of the status of your machine. You can see examples of it in operation here on my machine and on KPLUG.org