Free list server software for linux

Streamnik Server project is an IPTV server based on the open codecs Ogg/Vorbis and Ogg/Theora. It can stream a number of different channels and is optimized to run on leased (virtual) servers. The program schedule is defined by an SQL database table and can be changed at runtime.

kraskarta is an interactive map engine. It is based on Macromedia Flash technology with server scripts written in Perl with a PostgreSQL database.
kraskartas features include the ability to search for a street and address, for a bus route, and for information about objects.
Enhancements:
- This is the first open release after being proprietary code.

BitWise Routing Server allows multiple PCs behind a router to make direct connections.

The BitWise Routing Server allows you to accept BitWise connections to multiple computers behind a router. Typically, using a router, you would set up port forwarding on BitWises client port (4137), and specify a single destination IP. This is fine until multiple users behind a router all need to accept incoming connections.

As shown by the picture at right, the Routing Server allows individual users to register themselves with the Routing Server, and then the Routing Server accepts all incoming connections and directs those connections to the appropriate user.

The Routing Server requires that your physical router support port forwarding with a way to specify different external and internal ports (this is sometimes labeled "UPnP" by many common home routers).

The Routing Server has several options allowing you to customize the Routing Server for your environment. Many of the options are self-explanatory. The two that are not are Listen on Port and IP filtering. IP filtering is explained in the next section.

The BitWise Routing Server listens on a different port than the BitWise IM client. This allows the Routing Server and the IM client to be run on the same computer without causing conflicts. You will want to set up your router (more detail in a later step) to shift the port of the incoming connections from 4137 to another port. It doesnt particularly matter which port you want to use, as long as it is not a port used by another program. The default port is 4200.

Depending on the complexity of the network, it may be desirable to filter the IP addresses that are allowed to register with the Routing Server. This can be done in the preferences. One very likely scenario would be limiting registrations to the 192.168.1.x IP addresses (192.168 is reserved for local networks). When specifying an IP as the comparison address, you can use any valid IP numbers for wildcards.

In the case shown here, the Routing Server will limit connections to computers having IP addresses of 192.168.1.x. Any number, 0 through 255, could be placed for x in the Routing Server preferences.

If you are not familiar with IP address classes and IP filtering, it will usually be safe to leave Any selected.

Setting up the physical router

The picture at right was taken from a Linksys router, other routers will have a similar capability, although it may be layed out differently. On some routers, the advanced port forwarding options are mistakingly labeled UPnP.

The router setup shows that we are accepting connections on port 4137 and then sending them inside the network on port 4200 (the default port). Enter the IP address of the machine on the network running the Routing Server, and make sure that the rule is enabled. You will want to enter a rule for both TCP and UDP (UDP is used only for voice).

Please consult your router manual for more detailed instructions about how to set up port forwarding on your specific model.

Configuring BitWise to use the Routing Server

In order for you to enjoy the connectivity benefits of the Routing Server, you will need to register with the Routing Server when you log in to BitWise. Prior to logging in to BitWise, click the Setup button next to the Connect button to open the BitWise Setup. There is an area to enter an address for the Routing Server, and to specify what port to use. The port must be the same as the port used above (4200 is the default).

Upon connecting to BitWise, you will be registered with the Routing Server. If you could not be registered, an error message will be displayed. Double-check that the correct address was entered in the Setup.

Registration with the Routing Server

Upon successfully registering with the Routing Server, the Routing Server will display the user name and the IP address of the registration. If you want to unregister a user, click on the username, and then click Unregister. Incoming connections will no longer be forwarded to the specified computer.

It is worth pointing out two things here. First, if you later log in from a different computer, and that computer is also set to use the Routing Server, you will be re-registered with your new IP address. Second, if you are unregistered, or move to another computer but are not set up to use the Routing Server, you will not be able to benefit from the services of the Routing Server.
By default, the Routing Server saves the registered user list when it is closed down.

Using the Routing Server

Assuming that everything is set up correctly, everyone that registers with the Routing Server when they log in to BitWise will be able to enjoy significantly increased connectivity with other BitWise users. As incoming connections are established, you will see the connections listed in the right pane of the Routing Server window. The IP address and the time of the connection is also displayed, and the connection is later marked when it is disconnected.

The disconnected/closed connections may be cleaned from the list at any time using the Clean List button. Only active connections will be left displayed.

Messa is an instant messager client and server. The client has a curses interface and works on the console.

Messa project supports multilingual messages and private messages. The server supports monoprocess operation (without threads), the ability to choose the listening port, and the ability to run under the console.

StatsServ is a little program which emulates an ever smaller IRC server (in regard to the commands it handles) and transfers statistics from IRC into a database. You can then use the data, for example, on a Web site where you want to display the latest statistics.

Statistics consist of the uptime of each server in the network, a list of channels, including their topic (except for secret (+s) and private (+p) channels), and the number of users in the network.

You can normally get these statistics via /stats u, /list, and /lusers (if /stats u is supported on the network and enabled for normal users).

httptype is a program that returns the http host software of a website. It is written in Perl.
httptype reads a list of http hosts and optionally the port number for each of these. It queries each host, displaying the type of HTTP server running on that host. It reads the http_proxy and no_proxy environment variables to determine whether to use a proxy or not.
httptype reads a list of http servers and, optionally, the port number for each of these. It then queries each of the hosts and displays the HTTP server software of the host.
Input may be read from a host file if specified using the --hosts switch:
httptype --hosts [hostfile]
If hostfile is omitted or `-, httptype reads from standard input. See Format of host file for more info.
A single host may be queried by passing its name on the command line:
httptype host [port]
If port is omitted, 80 is used.
If no host file is specified through the --hosts file and no host is specified on the command line, httptype will read the list from standard input. See Format of host file for more info.
httptype will read the http_proxy environment variable and try to determine if a proxy server is being used. This setting may be overridden using the --proxy switch:
httptype --proxy proxyhost[:proxyport]
If proxyport is omitted, 80 is used.
If the proxy server is `none, no proxy is used. This is typically used to prevent httptype from using the proxy server specified by http_proxy. The --noproxy switch can be used to achieve the same.
Additionally, you may use the no_proxy environment variable to specify a comma delimited list of hosts for which httptype should not use the proxy. If httptype comes across any of these hosts, it will make a direct connection to them.
Enhancements:
- made 1.3.8 stable and renamed to 1.2.3

List::Intersperse Perl module can intersperse / unsort / disperse a list.

SYNOPSIS

use List::Intersperse qw/intersperseq/;

@ispersed = intersperseq {substr($_[0],0,1)} qw/A1 A2 B1 B2 C1 C2/;

@ispersed = List::Intersperse::intersperse qw/A A B B B B B B C/;

intersperse and intersperseq evenly distribute elements of a list. Elements that are considered equal are spaced as far apart from each other as possible.

FUNCTIONS

intersperse LIST

This function returns a list of elements interspersed so that equivalent items are evenly distributed throughout the list.

intersperseq BLOCK LIST

intersperseq works like intersperse but it applies BLOCK to the elements of LIST to determine the equivalance key.