Free celsius software for linux

Wmsensormon is a doc app for WindowMaker that utilizes lm_sensors to monitor CPU temp, sys temp, fan speeds, and CPU voltage.
It offers configurable warnings for overheating, and the sensors displayed are adjustable by the user with command line parameters.
Installation:
make
make install
wmsensormon
Options:
-h, --help this help screen
-v, --version print version information
-f show temperatures in Fahrenheit
-s default SMP mode (mode #1)
-s1 SMP mode #1 (CPU 1, CPU 2, sys, fan)
-s2 SMP mode #2 (CPU 1, CPU 2, fan 1, fan 2)
-sw switch CPU and SYS temperature readings
use with -s1 or -s2 if SYS temp is first
-swf switch fans to read fan3 and fan4
-r refresh time (in microseconds, default 100000)
-l enable logging with default time, (default 30000)
-ln enable logging with specified time, (1000 = 1 min)
-dt danger CPU temperature, default: system value (i.e. 60)
input values in Celsius
-ds danger SYS temperature, default: system value (i.e. 60)
input values in Celsius
-df danger fan speed, default: system value (i.e. 3000)
-wt warning CPU temperature, default: danger value
input values in Celsius
-ws warning SYS temperature, default: danger value
input values in Celsius
-wf warning fan speed, default: danger value
-lv limit CPU core volts, default is system value either: max voltage first, min
voltage second (i.e. 180 170) or:
percent difference first, value second (i.e. % 5 175)
Enhancements:
- when a command line arg gets a invalid parameter return error rather than ok
- fixed reading in the limit values from the wrong sensor if using the -sw option
- added option to choose a sensors chip to read from.
- added support for detecting whether the chosen sensor chip is a temperature sensor or some other type.
- if the choosen chip is number 0 or no chip is chosen, autodetect the chip to use.

EPoX wmsensormon is a hack based on the original wmsensormon package, version 1.1.3.
My modified version works out of the box on an 2.6.6 Linux kernel using the w83627hf and i2c-isa modules for hardware sensor monitoring, for an EPoX 8RDA3I motherboard.
Take it or leave it, dont call me for support.
Usage details
Compile by issuing make under the wmsensormon directory. You may need to add some -I and -L flags to the Makefile for your particular setup.
For me it works best when run like this:
wmsensormon -s1 -lf 2850 -lt 50 -ls 24
You can, of course, adjust the limits as you see fit, but only use integer values. Run wmsensormon without parameters to get help. The -lf is the lower CPU fan limit, -lt is the upper CPU and MOB temperature limit, -ls is the upper SYS temperature limit.
I dont use any of the additional features (logging, safety command, temperature switching) so they are untested. SMP support has been mangled and disabled so it most likely wont work in a multi-processor environment.
Options : -h, --help this help screen
-v, --version print version information
-f show temperatures in Fahrenheit
-s default SMP mode (mode #1)
-s1 SMP mode #1 (CPU 1, CPU 2, sys, fan)
-s2 SMP mode #2 (CPU 1, CPU 2, fan 1, fan 2)
-w switch CPU and SYS temperature readings
-r refresh time (in microseconds, default 100000)
-l enable logging with default time, (default 30000)
-ln enable logging with specified time, (1000 = 1 min)
-lt limit CPU temperature, default: system value (i.e. 60)
input values in Celsius
-ls limit SYS temperature, default: system value (i.e. 60)
input values in Celsius
-lf limit fan speed, default: system value (i.e. 3000)
-lv limit CPU core volts, default is system value
either: max voltage first, min voltage second (i.e. 180 170)
or: percent difference first, value second (i.e. % 5 175)
Example command line:
limit temp, fan, volt: wmsensormon -lt 40 -ls 30 -lf 5000 -lv 183 167 -f
using percent and SMP: wmsensormon -lt 40 -ls 30 -lf 5000 -lv % 5 175 -s -f
You must specify at least one command line argument, do to the fact that not everyone has the same CPU, voltage, or fan setup.
Enhancements:
- Hacked by xlife@zuavra.net to work on my new EPoX 8RDA3I.
- Displays CPU, MOB, SYS and FAN and reacts to lf, lt and ls limits.

Math::NumberCruncher Perl module contains a collection of useful math-related functions.

SYNOPSIS

It should be noted that as of v4.0, there is now an OO interface to Math::NumberCruncher. For backwards compatibility, however, the previous, functional style will always be supported.

# OO Style

use Math::NumberCruncher;

$ref = Math::NumberCruncher->new();

# From this point on, all of the subroutines shown below will be available # through $ref (i.e., ( $high,$low ) = $ref->Range( @array )). For the sake # of brevity, consult the functional documentation (below) for the use # of specific functions.

# Functional Style

use Math::NumberCruncher;

($high, $low) = Math::NumberCruncher::Range(@array);
$mean = Math::NumberCruncher::Mean(@array);
$median = Math::NumberCruncher::Median(@array [, $decimal_places]);
$odd_median = Math::NumberCruncher::OddMedian(@array);
$mode = Math::NumberCruncher::Mode(@array);
$covariance = Math::NumberCruncher::Covariance(@array1, @array2);
$correlation = Math::NumberCruncher::Correlation(@array1, @array2);
($slope, $y_intercept) = Math::NumberCruncher::BestFit(@array1, @array2 [, $decimal_places]);
$distance = Math::NumberCruncher::Distance($x1,$y1,$z1,$x2,$y2,$z2 [, $decimal_places]);
$distance = Math::NumberCruncher::Distance($x1,$y1,$x1,$x2 [, $decimal_places]);
$distance = Math::NumberCruncher::ManhattanDistance($x1,$y1,$x2,$y2);
$probAll = Math::NumberCruncher::AllOf(0.3,0.25,0.91,0.002);
$probNone = Math::NumberCruncher::NoneOf(0.4,0.5772,0.212);
$probSome = Math::NumberCruncher::SomeOf(0.11,0.56,0.3275);
$factorial = Math::NumberCruncher::Factorial($some_number);
$permutations = Math::NumberCruncher::Permutation($n);
$permutations = Math::NumberCruncher::Permutation($n,$k);
$roll = Math::NumberCruncher::Dice(3,12,4);
$randInt = Math::NumberCruncher::RandInt(10,50);
$randomElement = Math::NumberCruncher::RandomElement(@array);
Math::NumberCruncher::ShuffleArray(@array);
@unique = Math::NumberCruncher::Unique(@array);
@a_only = Math::NumberCruncher::Compare(@a,@b);
@union = Math::NumberCruncher::Union(@a,@b);
@intersection = Math::NumberCruncher::Intersection(@a,@b);
@difference = Math::NumberCruncher::Difference(@a,@b);
$gaussianRand = Math::NumberCruncher::GaussianRand();
$ways = Math::NumberCruncher::Choose($n,$k);
$binomial = Math::NumberCruncher::Binomial($attempts,$successes,$probability);
$gaussianDist = Math::NumberCruncher::GaussianDist($x,$mean,$variance);
$StdDev = Math::NumberCruncher::StandardDeviation(@array [, $decimal_places]);
$variance = Math::NumberCruncher::Variance(@array [, $decimal_places]);
@scores = Math::NumberCruncher::StandardScores(@array [, $decimal_places]);
$confidence = Math::NumberCruncher::SignSignificance($trials,$hits,$probability);
$e = Math::Numbercruncher::EMC2( "m512", "miles" [, $decimal_places] );
$m = Math::NumberCruncher::EMC2( "e987432" "km" [, $decimal_places] );
$force = Math::NumberCruncher::FMA( "m12", "a73.5" [, $decimal_places] );
$mass = Math::NumberCruncher::FMA( "a43", "f1324" [, $decimal_places] );
$acceleration = Math::NumberCruncher::FMA( "f53512", "m356" [, $decimal_places] );
$predicted_value = Math::NubmerCruncher::Predict( $slope, $y_intercept, $proposed_x [, $decimal_places] );
$area = Math::NumberCruncher::TriangleHeron( $a, $b, $c [, $decimal_places] );
$area = Math::NumberCruncher::TriangleHeron( 1,3, 5,7, 8,2 [, $decimal_places] );
$perimeter = Math::NumberCruncher::PolygonPerimeter( $x0,$y0, $x1,$y1, $x2,$y2, ... [, p$decimal_places]);
$direction = Math::NumberCruncher::Clockwise( $x0,$y0, $x1,$y1, $x2,$y2 );
$collision = Math::NumberCruncher::InPolygon( $x, $y, @xy );
@points = Math::NumberCruncher::BoundingBox_Points( $d, @p );
$in_triangle = Math::NumberCruncher::InTriangle( $x,$y, $x0,$y0, $x1,$y1, $x2,$y2 );
$area = Math::NumberCruncher::PolygonArea( 0, 1, 1, 0, 2, 0, 3, 2, 2, 3 [, p$decimal_places] );
$area = Math::NumberCruncher::CircleArea( $diameter [, $decimal_places] );
$circumference = Math::NumberCruncher::Circumference( $diameter [, $decimal_places] );
$volume = Math::NumberCruncher::SphereVolume( $radius [, $decimal_places] );
$surface_area = Math::NumberCruncher::SphereSurface( $radius [, $decimal_places] );
$years = Math::NumberCruncher::RuleOf72( $interest_rate [, $decimal_places] );
$volume = Math::NumberCruncher::CylinderVolume( $radius, $height [, $decimal_places] );
$volume = Math::NumberCruncher::ConeVolume( $lowerBaseArea, $height [, $decimal_places] );
$radians = Math::NumberCruncher::deg2rad( $degrees [, $decimal_places] );
$degrees = Math::NumberCruncher::rad2deg( $radians [, $decimal_places] );
$Fahrenheit = Math::NumberCruncher::C2F( $Celsius [, $decimal_places] );
$Celsius = Math::NumberCruncher::F2C( $Fahrenheit [, $decimal_places] );
$cm = Math::NumberCruncher::in2cm( $inches [, $decimal_places] );
$inches = Math::NumberCruncher::cm2in( $cm [, $decimal_places] );
$ft = Math::NumberCruncher::m2ft( $m [, $decimal_places] );
$m = Math::NumberCruncher::ft2m( $ft [, $decimal_places] );
$miles = Math::NumberCruncher::km2miles( $km [, $decimal_places] );
$km = Math::NumberCruncher::miles2km( $miles [, $decimal_places] );
$lb = Math::NumberCruncher::kg2lb( $kg [, $decimal_places] );
$kg = Math::NumberCruncher::lb2kg( $lb [, $decimal_places] );
$RelativeStride = Math::NumberCruncher::RelativeStride( $stride_length, $leg_length [, $decimal_places] );
$RelativeStride = Math::NumberCruncher::RelativeStride_2( $DimensionlessSpeed [, $decimal_places] );
$DimensionlessSpeed = Math::NumberCruncher::DimensionlessSpeed( $RelativeStride [, $decimal_places] );
$DimensionlessSpeed = Math::NumberCruncher::DimensionlessSpeed_2( $ActualSpeed, $leg_length [, $decimal_places]);
$ActualSpeed = Math::NumberCruncher::ActualSpeed( $leg_length, $DimensionlessSpeed [, $decimal_places] );
$eccentricity = Math::NumberCruncher::Eccentricity( $half_major_axis, $half_minor_axis [, $decimal_places] );
$LatusRectum = Math::NumberCruncher::LatusRectum( $half_major_axis, $half_minor_axis [, $decimal_places] );
$EllipseArea = Math::NumberCruncher::EllipseArea( $half_major_axis, $half_minor_axis [, $decimal_places] );
$OrbitalVelocity = Math::NumberCruncher::OrbitalVelocity( $r, $a, $M [, $decimal_places] );
$sine = Math::NumberCruncher::sin( $x [, $decimal_places] );
$cosine = Math::NumberCruncher::cos( $x [, $decimal_places] );
$tangent = Math::NumberCruncher::tan( $x [, $decimal_places] );
$arcsin = Math::NumberCruncher::asin( $x [, $decimal_places] );
$arccos = Math::NumberCruncher::acos( $x [, $decimal_places] );
$arctan = Math::NumberCruncher::atan( $x [, $decimal_places] );
$cotangent = Math::NumberCruncher::cot( $x [, $decimal_places] );
$arccot = Math::NumberCruncher::acot( $x [, $decimal_places] );
$secant = Math::NumberCruncher::sec( $x [, $decimal_places] );
$arcsec = Math::NumberCruncher::asec( $x [, $decimal_places] );
$cosecant = Math::NumberCruncher::csc( $x [, $decimal_places] );
$arccosecant = Math::NumberCruncher::acsc( $x [, $decimal_places] );
$exsecant = Math::NumberCruncher::exsec( $x [, $decimal_places] );
$versine = Math::NumberCruncher::vers( $x [, $decimal_places] );
$coversine = Math::NumberCruncher::covers( $x [, $decimal_places] );
$haversine = Math::NumberCruncher::hav( $x [, $decimal_places] );
$grouped = Math::NumberCruncher::Commas( $number );
$SqrRoot = Math::NumberCruncher::SqrRoot( $number [, $decimal_places] );
$square_root = Math::NumberCruncher::sqrt( $x [, $decimal_places] );
$root = Math::NumberCruncher::Root( 55, 3 [, $decimal_places] );
$root = Math::NumberCruncher::Root2( 55, 3 [, $decimal_places] );
$log = Math::NumberCruncher::Ln( 100 [, $decimal_places] );
$log = Math::NumberCruncher::log( $num [, $decimal_places] );
$num = Math::NumberCruncher::Exp( 0.111 [, $decimal_places] );
$num = Math::NumberCruncher::exp( $log [, $decimal_places] );
$Pi = Math::NumberCruncher::PICONST( $decimal_places );
$E = Math::NumberCruncher::ECONST( $decimal_places );
( $A, $B, $C ) = Math::NumberCruncher::PythagTriples( $x, $y [, $decimal_places] );
$z = Math::NumberCruncher::PythagTriplesSeq( $x, $y [, $decimal_places] );
@nums = Math::NumberCruncher::SIS( [$start, $numbers, $increment] );
$inverse = Math::NumberCruncher::Inverse( $number [, $decimal_places] );
@constants = Math::NumberCruncher::CONSTANTS( all [, $decimal_places] );
$bernoulli = Math::NumberCruncher::Bernoulli( $num [, $decimal_places] );
@bernoulli = Math::NumberCruncher::Bernoulli( $num );