Free router simulator rapidshare software for linux

Jimsim Network Simulator project can emulate several routers connected via virutal networks. You can connect to the routers with your own favorite telnet program.
Connecting to the Virtual Routers
Use your favorite telnet program to connect to each of the virtual routers. For example:
For router 1 type:
C:>telnet localhost 10000
For router 2 type:
C:>telnet localhost 10001
For router 3 type:
C:>telnet localhost 10002
Network Layout
Currently the network is configured like this:
access-list [1-99] [permit/deny] [ ip wildcard-mask | host a.b.c.d | any ]
ip acccess-list [standard] [name]
ip access-group
show access-list
show ip interface
show ip interface brief
debug interface
encapsulation [hdlc,ppp] (serial interfaces only)
bandwidth
clock rate (serial interfaces)
interface loopback0
User commands:
?
enable
exit
ping ip
show cdp
show cdp neigh
show cdp neigh detail
show interface
show interface e0,eth0,etc
show ip route
show version
Enable commands:
clear counters
clear counters interface
config terminal
copy running startup
copy startup running
debug all
debug ip routing
debug ip eigrp
debug cdp
disable
exit
reload
show run
show startup
show ip eigrp neighbors
show ip eigrp topology
traceroute ip
undebug all
undebug ip routing
undebug ip eigrp
undebug cdp
Config commands:
cdp run
enable password password
end
hostname
banner motd delimiter
banner exec delimiter
banner login delimiter
ip route network netmask dest
interface e0,eth0,etc
bandwidth value
ip address addr netmask
description
cdp enable
shutdown
line con0, console0, console 0
login
login local
password passwd
router eigrp number
network a.b.c.d
service password-encryption
user username password password
Version restrictions:
- The EIGRP support is very basic. Just the network command for now. (Neighbors dont expire.) You can disable EIGRP with "no router eigrp process_id"
- The routing table isnt 100% correct. It doesnt summarize subnets. Nor does it understand multiple routes to the same destination. This will be fixed in the next version.
- Traceroute seems to count extra hops. Its counting each remote interface on a router as a hop. So, when you traceroute from router1 to router3, it counts router2 twice (once for 192.168.1.2 and 10.1.1.1)

Simulator 8085 is a simulator of the 8085 MP for KDE (3.1 and 3.2pre) that allows you write code in a text editor.

After assembling, the hex code is readable alongside the mnemonics. It can handle jumping labels and strings, and you can choose beetween a single or multiple window interface. All 8085 MP inclusive interrupts work.

GTP server simulator is a simple responder for the GTP (GTP prime) protocol that works with the Cisco Content Services Gateway to provide per-user traffic limits.

GTP` (GTP prime) server simulator (it permits any content and provide quadrants for every operation) binaries for Linux (run under Fedora Core 4 and 5).

The binary was tested with Cisco CSG.

Linux LiveCD Router project allows you to share and firewall your broadband connection and use WIFI.
You can use DSL, ADSL, Cable Modem, T1, Fixed IPs, Dial-Up, WIFI, build you own Access Point and more.
Main features:
- Share and Firewall your broadband or dedicated Internet connection
- Includes Firewall Shorewall and Masquerading (NAT)
- Does not require any installation. It is a LiveCD, your computer simply boots straight from the CD. Does not require a hard disk
- Supports DSL, Cablemodem, Fixed IP and Dial-Up
- Traffic Control, QoS
- DHCP Client and Server
- Remote SSH administration
- Includes DNS Cache to accelerate surfing
- Includes SNMP Monitoring, MRTG graphical statistics
- Use standard and low cost computer, networking and wifi hardware (also USB)
- Can use multiple ethernet and wifi 802.11a/b/g cards. Supports PCI, USB and PCMCIA cards (can replace external Access Points!)
- Linux Software compatible with Windows and Mac Networks

Network Simulator (Ns) is a discrete event simulator targeted at networking research. Ns provides substantial support for simulation of TCP, routing, and multicast protocols over wired and wireless (local and satellite) networks.
Ns began as a variant of the REAL network simulator in 1989 and has evolved substantially over the past few years. In 1995 ns development was supported by DARPA through the VINT project at LBL, Xerox PARC, UCB, and USC/ISI.
Currently ns development is support through DARPA with SAMAN and through NSF with CONSER, both in collaboration with other researchers including ACIRI. Ns has always included substantal contributions from other researchers, including wireless code from the UCB Daedelus and CMU Monarch projects and Sun Microsystems.
Enhancements:
- Major updates were made to the PackMime-HTTP HTTP/1.1 and WPAN modules.
- Solaris/Sun C compilation bugs were fixed.

Fungus Agent Simulator project consists of a distributed multi-agent-based simulator.
Fungus Agent Simulator is a distributed multi-agent-based simulator that lets users easily create artificial life simulations. It uses a modular and a extensible architecture. A tiny scripting language (named Mycelium) is provided.
With Mycelium, users can easily build a simulation. Users can access the information traveling between the agents. Multiple scheduling models and multiple view are provided.
Main features:
- Agent
- Agent Based Simulation
- Agent could be a object or a threaded object
- Hierarchical agent
- Communication
- Messages passing communication model
- Discrete Event
- Communications canals are accessible
- Kernel
- Manage Scheduling Techniques
- distributed simulation
- Graphical user interface
- Simulator is written in Java

Snow Path Formation Simulator is a program that models the process of people forming very distinct, and yet not always altogether logical looking, paths in the snow as they walk across open spaces.

The evolving condition of the snow is displayed graphically. This project may eventually mature into a screensaver.