Free mrtg ping probe 2.2.0 software for linux

IPmonitor just a simple IP or url monitor, using PING command to check if the given addresses are alive.

RogueScanner project is an open-source vulnerability management tool that is used to gain greater network visibility to enable you to quickly identify and remove rogue wireless devices that may provide a back door to access your critical data and infrastructure.

Considering that rogue access points and peers represent a major threat to data integrity, RogueScanner is a valuable tool that you can start using today at no cost.
More than 300 companies manufacture access points, and there are more than 10,000 different models of network infrastructure.

Companies thus face a major challenge in maintaining a system to track and identify all potential rogue wireless devices and in continually scanning the network to identify them. To address this challenge, Network Chemistry has made an open-source product available to help organizations begin to immediately scan their networks.

RogueScanner is available for use at no charge by organizations looking for a tool focused on device identification and rogue detection. RogueScanner leverages the Collaborative Device Classification system to automatically lookup and identify the device type and its identity in real time.

Whats New in This Release:

+ Reserved VLANs (1000 < VLAN < 1025) on Cisco devices are not queried.
+ Capture packets to trace.pcap and perform a hexdump of them in the log file
if DEBUG_PACKET is set (debug=0x01 or better).
+ Promiscuous mode testing is disabled unless ENABLE_SCAN_PROMISC is defined.
+ The switch/network scanning interval was bumped up to 24 hours.
+ Attribute data in the EvidenceMap wasnt being printed out correctly (always showed
up as "true") when issuing "device detail" commands in the CLI.
+ Ignore MACs in the bridge table that arent "learned" when querying switches.
+ *TAnalysisManager::LookupOrCreateDevice() will now refuse to create devices outside
"home_net" ranges, thus the IPs wont be scanned even if they are passively observed
on the local network.
+ Ignore our MAC address if a switch reports it to us.
+ Log timestamps are now in GMT.
+ Prevent duplicates in the "udp_ports" evidence by using AddEvidence() instead of
inserting into the EvidenceMap directly.
+ Manually invoke Rubys garbage collector after scanning a switch/router.
+ Added "packet queue size" CLI command to show how many packets are in the
AnalysisManagers packet queue.
+ If a device fails to be classified the classification will be retried automatically
in one minute.
+ All communication with the classification server is performed in a separate thread.
+ Keep ARP scanning from starving other threads for CPU time by introducing a delay
in addition to any that is added by bandwidth throttling.
+ Replaced internal ARP and routing table on WIN32 systems with functions from the
IPHelper API.
+ Added "device list size" command to show how many devices have been found.
+ Add read community strings from configured infrastructure devices to the list
of strings used when probing unknown devices.
+ Discard deferred scans if another scan of the same type is already deferred for
a device.
+ Added reporting of DHCP data.
+ If no scans are pending against a device, but a new port is found open then
submit the devices evidence.
+ Devices are re-scanned whenever a re-occuring ARP/Ping scan is launched.
+ Added "deferred list" CLI command to show scans that have been deferred.
+ Added "sniffer status" CLI command to report the number of packets that
have been received and dropped.
+ If we discover the IP of a device that we only knew about the MAC address for,
then issue scans against it.
+ If we see the MAC address associated with an IP change, then re-scan it since
its likely to be a different device.

mrtg-misc-probe probes different system features for mrtg to graph.
Currently it can probe:
- percent usage of disk space and inodes for UFS filesystems
- percent usage of disk space for VxFS filesystems
- incoming and outgoing mail messages on sendmail mail server
- total size of mail messages sendt and received on sendmail mail server
- network delay using NTP peers/servers
- number of ClearCase vobs and views
- number of available and used ClearCase and MultiSite licenses
- number of active and disconnected sessions of a Citrix Metaframe server
- number of reachable hosts in a given network range
- network device reachability (ping success)
Enhancements:
- New probes: ctxmf - number of active and disconnected Citrix Metaframe sessions; hostcount - scan given nmap-network-range and return number of hosts found.

MRTG-eth-probe provides a probe for the Multi Router Traffic Grapher, generating statistics for network devices that do not support the SNMP protocol. It reads interface stats from /proc/net/dev (or some other file you configure), and generates an output readable for MRTG by parsing the file.
Since the starting of this project MRTG-eth-probe has been downloaded more than 1700 times (as of 2001-11-04). Thanks for this go first of all to Freshmeat for accepting the project and for redirecting so much people to my sourceforge projectpage Additional thanks go to Michael Feger for sending me a patch to 1.5.2 which makes up the most important changes of this release.
Enhancements:
- bugfix: missing dot

THC-Probe is the ultimate host scanner compilation for Linux, featuring nmap, snmpscan, netbios auditing tool and super-cool vh shell script.

INSTALL: just run "make install". Everything will be installed in /usr/local

RUN: just run "netprobe" and see the options.

Every host scanned will be saved as a "host.bla.com.probe" file in your current directory.

It does many stuff like snmp guessing, samba pw guessing and information gathering.

Nothing great and big, but it suits my needs.

GNU FreeIPMI project provides "Remote-Console" (out-of-band) and "System Management Software" (in-band) based on IPMI v1.5/2.0 specification.
This project includes:
- KCS, SMIC, SSIF, LAN Drivers and C Library (libfreeipmi)
- IPMI Locate - Probe IPMI BMC Device (ipmi-locate)
- FreeIPMI SHell (fish)
- Watchdog Daemon (bmc-watchdog)
- Sensors (sensors)
- System Event Log (sel)
- BMC Info (bmc-info)
- BMC Config (bmc-config)
- IPMI Power (ipmipower)
- IPMI Ping (ipmiping)
- RMCP Ping (rmcpping)
- Gratuitous ARP Daemon (garpd)
- IPMI Raw Interface (ipmi-raw)

PingBlog is a tag generator and ping tool for blog directories such as Blogalaxia, VeneBlogs, Technorati, To2Blogs and others.

Dynamic Probe Class Library (DPCL) is an object-based C++ class library that provides the necessary infrastructure to allow tool developers and sophisticated tool users to build parallel and serial tools through technology called dynamic instrumentation.
Dynamic Probe Class Library takes the basic components needed by tool developers and encapsulates them into C++ classes. Each of these classes provide the member functions necessary to interact and dynamically instrument a running application with software patches called probes.
Dynamic instrumentation provides the flexibility for tools to insert probes into applications as the application is running and only where it is needed.
Enhancements:
- This version is a minor update to DPCL that fixes a couple problems that have been reported since the v3.4.2 release